Technical assistance
We want to clear the main technical questions that may arise about the operation of our products and the steps necessary for their assembly.
Accessories for wardrobe
The gap between the side of the module and the frame / guides of the Keeper interior cabinet or dresser accessories is 25mm.
The gap between the side of the module and the frame / rails of the Hack interior cabinet or walk-in closet accessories is a minimum of 20mm.
We would like to remind you that in the case of folding-door or hinged-door assembly, the hanger must go with the lateral supplement.
The following video shows how you can easily assemble the pull out lateral shoe rack.
The finishes for these supports are RAL9006 for the aluminium colour and RAL8019 for the Moka colour.
According to the ISO: 7170:2005 standard, the bracket for circular hanging bars or round tubes can tolerate a maximum weight of 40 kg/metro uniformly spread out.
Yes, the Self trouser holder stands out for its ease of installation and because it can change sides easily. In order to change the position of the trouser holder it is only necessary to unscrew the central body and separate it from the runners in order to change side, and unscrew the cylindrical handle and put it on the other side.This trouser rail incorporates 37 mm full-extension ball bearing runners with a gentle sliding movement and a handle for pulling out of the furniture. Also, it has eleven chrome steel bars with non-slip rubbers for hanging trousers on.
Yes, it is only necessary to cut the cross profiles of the Keeper frame with a straight cut. In this manner you can attain an inside width of the unit less than 555 mm.Afterwards, it will be necessary to bear in mind the new measurement of the frame in order to add the different accessories such as baskets, drawers and trouser racks.
The RAL of the finish of the accessories for inside Moka wardrobes and dressing rooms is approximately 8019.
The following video shows how you can easily assemble the extractable shoe rack Moka.
Yes, the Moka trouser holder is available in two models, for assembly on either the right hand side or left hand side of the wardrobe, and to that end there are different codes. This completes the range of furnishing and storage options for your wardrobe or dressing room.
The following video shows how you can easily assemble the pull out lateral shoe rack Moka.
Yes, this mirror has 45 mm guides with bearings and a trigger for detaching it.It also has free rotation up to 180º so you can position it comfortably.It is easy and quick to install, without mechanisms, simply by screwing it into the unit. To make it even easier, it comes with the screws required for assembly.
The Moka mirror is assembled on the side of a unit and needs a minimum width of 225 mm in order for the mirror to be extractable and rotating.
The following video shows how you can easily assemble the pull-out mirror Moka.
The following video shows how you can easily assemble the pull-out hanging rail Moka.
The following video shows how you can easily assemble the lateral pull-out tie rack Moka.
The side supplement of the Hang fold-down hanger is used to increase the distance between the hanger and the side of the unit, avoiding the arms of the hinges. Thanks to this supplement, you will be able to mount the Hang hanger fully integrated into your wardrobe with hinged doors.
The following video shows how you can easily assemble the Hang Moka wardrobe lifts.
Yes, you simply need to respect the minimum installation depth of the Moka runners and carry out the assembly with the clips that are supplied.
The gap between the side of the module and the frame / rails of the Moka closet or dressing room interior accessories is 9mm.
The following video shows how you can easily assemble the Moka accessories.
The following video shows how you can easily assemble the Sling wardrobe lifts.
According to the ISO standard: 7170:2005 Emuca supports can take a maximum weight of 40 kg per metre evenly distributed.
Silk wardrobe rail central support
Silk wardrobe rail angular support
Wardrobe rail lateral support 90168
Direct assembly wardrobe rail lateral support
Wardrobe rail lateral support 40070
Wardrobe rail lateral support 60474
Wardrobe rail lateral support 71468
Wardrobe rail lateral support 60026
Silk wardrobe rail support set
Wardrobe rail central support 81203
Luxe wardrobe rail central support
Luxe wardrobe rail support set
Luxe wardrobe rail angular support
Luxe wardrobe rail support set, plastic
Steel wardrobe rail
Aluminium wardrobe rail
Luxe rectangular wardrobe rail kit
Silk wardrobe rail kit
Luxe rectangular rail for Zero structure
Wardrobe hanging rail kit 30x15 mm steel
Wardrobe hanging rail kit 30x15 mm aluminium
Wardrobe hanging rail kit Silk
Wardrobe rail lateral support 70143
The following video shows how you can easily assemble the Luxe supports.
The following video shows how you can easily assemble the Luxe supports.
The following video shows how you can easily assemble the Luxe supports.
Modular shelving
Yes, the structure must be fixed to the wall in all cases to avoid it tipping over.
The following video shows how you can easily install the Zero system.
The following video shows how you can easily install the Zero system.
The following video shows how you can easily install the Zero system.
The following video shows how you can easily install the Zero system.
The following video shows how you can easily install the Zero system.
Tool assembly set for Zero rectangular leveller (Floor – Wall)
Zero modular structure kit with tools and profiles to be assembled in the floor and the wall shape
Set of rectangular levelers for mounting Zero profiles (Floor - Ceiling)
Profile for Zero modular structures
Piece to affix the Zero profile to the wall
Joint between Zero profiles
The shelf support for a gap slot of 32 mm has two through holes, which enable access through a screw and a manual tool. This makes it possible to fasten the board if that is required, especially in assemblies with very wide continuous shelves.
Profiles and accessories for wooden doors
It is designed for board thicknesses greater than 15 mm and it is advisable to mount 2 tensioners per door when the width is greater than 600 mm.
Yes, the Even tensioner can be cut at both ends to achieve the desired size.
When you assemble a wardrobe with a system of sliding doors it is necessary to mount handle profiles for opening and closing. In the Emuca catalogue there are different models created from aluminium and steel.Depending on the sliding door system chosen, you can use certain handle profiles or other depending on their geometry. In the following table you can find the compatibility that exists between different sliding door systems and handle profiles.u Compatible and ideal.\- Compatible but not ideal.x Not compatible.
Generally, in our catalogue there are two forms of sale for profiling items:Package sales: For that reason we have profiles cut to the specific measure (for example 3m) and packaged in the quantity outlined in the catalogue (for example 24m packaging). They are for immediate delivery as we have stock and they can be managed through our B2B.Made to measure sales: For this purpose we have profiles in industrial packaging (for example m packaging) and in this way, our clients can request profiles made to a specific measure. The maximum cut measurement that can be requested is the length of the bar indicated with L (for example 3m).This sales method implicitly involves extra management, opening codes, for opening codes, handling, cutting and packaging, as well as an extra delivery period from the order date.These products can be requested through our B2B, although the assessment of the order (final price) is outstanding until the Customer Service Area gets in touch with the client in order to define the exact measurement, the quantity of profiles requested and the delivery period.
Aluminium doors
The following sketch shows details of the machining that should be carried out for the bracket of the Plus 7 aluminium profiles.
The following sketch shows details of the machining that should be carried out for the bracket of the Plus 17 aluminium profiles.
The following sketch shows details of the machining that should be carried out for the bracket of the Plus 15 aluminium profiles.
The following sketch shows details of the machining that should be carried out for the bracket of the Plus 14 aluminium profiles.
The following sketch shows details of the machining that should be carried out for the bracket of the Plus 4-4E-11-16-18 aluminium profiles.
The following sketch shows details of the machining that should be carried out on aluminium doors for the Aluroller 2 sliding system.
The double-sided adhesive table, Code. 6000215 is white acrylic foam tape that is 33x19mm with a thickness of 0.64mm. This tape has an acrylic adhesive that offers excellent adhesion to several finishes and plasticized vinyl. Likewise, it is resistant to solvents, extreme temperatures and UV rays, therefore it is recommended for several uses inside and outside.In the attached document, you can see details of the technical characteristics of the double-side adhesive tape, code. 6000215.
The calculation for adhesive tape that should be used to guarantee the correct fastening of the glass is defined by the size of the door designed. For this task we have a simple calculation table.
Documents:
DownloadThey can be removed or concealed in different ways depending on the type of stains.Small black graze marks can be eliminated by simply rubbing them with a rubber used to rub out pencil.With small shiny lines, you simply need to rub the area with a scouring pad (scotch-brite type) soaked in methylated spirits.For small white circular marks, you can rub with the area with a scouring pad or cloth with Vaseline or some greasy substance.
According to the number of doors that comprise your wardrobe you can choose between different types of Free aluminium vertical profiles (A, B or C) to obtain different combinations of doors. Type A. Central door used to create wardrobes with three doors. Created with two handle profiles. Type B. Outer door used to create wardrobes with two or four doors. Created with a handle profile and a handle cover profile. Type C. Inside door used to create wardrobes with two or four doors. Created with a vertical profile and a handle profile.
The following video shows how the sliding door system for wardrobes is assembled.
Although the he adjustable, visible, hanging Neco sliding system allows for a maximum door thickness of 30 mm, the fittings and profiles of the Free aluminium door do not allow for the assembly of this sliding door system.
For the assembly of the Free poor alongside the Space + sliding door system, it is necessary to choose an outside runner with a thickness of 30 mm.
For the assembly of Free Face profile hands for board of 19-20 mm alongside the Space+ sliding door system, it is necessary to choose an outside runner with a thickness of 30 mm and adhesive spacer cod. 4000820. For the assembly ofFree Face 2 profile hands for board of 19-20 mm alongside the Space+ sliding door system, it is necessary to choose an outside runner with a thickness of 23 mm.
