Technical assistance

We want to clear the main technical questions that may arise about the operation of our products and the steps necessary for their assembly.

Extendable tables slides

The following video shows how you can easily assemble the Twice Top mechanism.

The following video shows how you can easily assemble the Corner mechanism.

The following video shows how you can easily assemble the Party mechanism.

The following video shows how you can easily assemble the Lunch+39 mechanism.

The following video shows how you can easily assemble the Lunch mechanism.

The following video shows how you can easily assemble the Shot mechanism.

Storage kitchens

The unit on which the Supra hinged column is installed requires at least 4 hinges for the column to work properly.To this end, we recommend installing the column with soft-close hinges X91 or C91E.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

No, a Supra bottle rack can only be assembled on the left-hand side, as you have the guide rails on the left-hand side.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

The minimum door size for installing a half-moon Shelvo rack in a kitchen unit will depend on the diameter of rack chosen: \- For racks of 650 mm diameter, the minimum door size is 400 mm. \- For racks of 750mm diameter, the minimum door size is 450 mm.

What is the minimum door size for installing a half-moon Shelvo rack?

No, a Titane bottle rack can only be assembled on the left-hand side, as you have the guide rails on the left-hand side.

The unit on which the Titane hinged column is installed requires at least 4 hinges for the column to work properly.To this end, we recommend installing the column with soft-close hinges X91 or X92.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

Waste containers

Bottom mounting and automatic extraction systems need to be larger than the width of the container. This is due to the fact that the attaching mechanism needs to occupy a larger space than the width of the container. However, you can always reduce the minimum size of the module and make it function with manual opening.

What is the minimum module size for installing bottom mounting containers with automatic extraction?

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

Yes, for panels of 16 mm thickness, is possible to use the module 500 mm Vantage-Q drawer.

Yes, the Recycle container be assembled on either a right or left-hand side door.You simply have to follow the assembly instructions, along with the assembly template.

The following video shows how you can easily assemble a Recycle extractable waste container for doors.

Gola Profiles

Household appliances that can be integrated are completely compatible with the Gola profile system (with or without bumper). Thanks to that compatibility, household appliances remain hidden, thus adding a sense of continuity to kitchen furniture.In order to facilitate the work of manufacturers and assemblers, it is only necessary to bear in mind that the sum of the height along with the base, needs to be greater than the height of the household appliance along with the upper Gola profile that is used. Also, the attached document shows details with practical examples.

How can I assemble household appliances that can be integrated along with the Gola profile system in low units in my kitchen?

The Gola system joining accessories are created using plastic (grey or white finish), and also, the accessories that are positioned on corners or corner edges require the profile to have a mitre joint.On the contrary, the straight cut accessories are created from matt silver anodized aluminium, and also, with all of them the profile only needs a straight cut, therefore preparation is easier.

What differences are there between the joining accessories of the Gola system and the straight cut joining accessories?

In order to install a Gola horizontal profile system in aluminium, it is necessary to use type A or B joining supports. These supports do not have handles and they make it easy to anchor or move the horizontal profiles simply and comfortably. Their pressure mounting or direct screwing requires machining of Ø10 mm in the side of the furniture.The difference between them is the distance between the edge of the machining to the centre of the drill hole. For the A support, it is 15 mm and for B it is 19.7 mm, both are valid for fastening the upper profile as well as the central profile.Depending on the distance of the machining that you want. you can choose one support or the other.

Which support should I choose, A or B, in order to install a Gola system?

In order to install the Gola profiles on a unit it is recommended to have gap measurements for being able to open the drawer or the door. These measurements are for guidance purposes and may vary depending on the overlaps.For an upper Gola profile it is recommended to have a 37 mm gap, and for a central Gola profile a 40 mm gap is recommended. The image shows a vertical view of the side of the unit.

What size of gap is it recommended to leave in order to be able to open a drawer or a door on a unit with a Gola profile?

The RAL code of the white finish of the profiles system Gola is approximately 9003.The RAL code of the anthracite grey finish of the the profiles system Gola is approximately 7043.The RAL code of the black finish is approximately 9011.

Kitchen

Yes, it can be combined with a wide range of our undermount recycling buckets. Please refer to the table below for compatibility:

Accessories for kitchen furniture

The following video shows how you can easily install the ironing board.

The following video shows how you can easily install the ironing board.

This container or dustbin needs a 270 mm free space inside the kitchen module or unit.

In order to assemble the plastic base for the fridge, such as the Fridge Base, it is necessary to have the kitchen Bone feet as well as the number 10 metric screw thread (M10) from the same family, as the base as four holes for fastening the feet.The Fridge Base is also perforated for ventilation and designed for fridges to be integrated into 600 mm wide units with tufts for assembly.

Yes, it's very easy. Simply use a ruler and cutter to trim the sink protector to the size you want.Run the cutter along the line several times, then bend along the cut and you can cut the aluminium panel.

We have protectors designed for assembly in kitchen floor units and in sink floor units.They are produced using natural textured aluminium with a plastic strip around the border that protects the unit from small leaks or from cleaning products.These protections are sized for 16 mm and 18 mm board, for special measurements consult the conditions.

We have an anti-slip mat that is supplied in rolls that are easy to cut to any inside measurement of the drawer. This mat has two roles:It prevents objects moving inside the drawer when it is opened or closed.It prevents the bottom of the drawer being damaged with a graze or little knock when handling objects stored in the drawer.

Yes, for panels of 16 mm thickness, is possible to use the module 500 mm Vantage-Q drawer.

The Optima cutlery holder has a wide range of models and sizes. The cutlery holder intended for the Vantage-Q drawer is not compatible with the Slim drawer. as a a cutlery holder model exists for the Slim drawer.Both models have the same depth but not the same width, specifically, the cutlery holders for the Slim drawer are 6 mm narrower than the cutlery holders for the Vantage-Q drawer.

The RAL code of the white finish of the Optima cutlery holder is approximately 9003. The RAL code of the grey finish of the Optima cutlery holder is approximately 7001. The RAL code of the anthracite grey finish of the Optima cutlery holder is approximately 7043.

Sut blinds can be adapted to different heights with a maximum height of 1500 mm. To do that, you simple need to cut the side rails and not fully unroll the blind. You need to bear in mind that the minimum gap for housing the blind box is 175 mm. However, the width of the Sut blind cannot be modified or cut, as this affects the pulling in mechanism of the blind.

The following video shows how you can easily assemble the abovementioned storage system in a kitchen.

The following video shows how you can easily assemble the microwave frame.

The following video shows how you can easily assemble the oven grille.

The distance between the rods of the dish draining rack is 18 mm.Each of the rods is 7 mm wide.

The following video shows how you can easily assemble the Inox plate racks.

Subscribe to notifications
You're subscribed to notifications
You've blocked notifications
Click to subscribe to notifications
Thanks for subscribing!
You're subscribed to notifications
You won't receive notifications again
Manage Site Notifications
SUBSCRIBE
UNSUBSCRIBE
Unblock Notifications
Follow these instructions to allow notifications: